PREGUNTA 1 de 20
Qué indica el índice de polarización de valor 3,5 en una máquina eléctrica.
⚪
A)
Que el aislamiento está húmedo y sucio.
⚪
B)
Que el aislamiento está seco y limpio.
⚪
C)
Que el aislamiento está relativamente contaminado.
⚪
D)
Que el aislamiento está fuertemente contaminado.
PREGUNTA 2 de 20
Las medidas de resistencia de aislamiento en las instalaciones eléctricas deben hacerse de la siguiente forma:
⚪
A)
Con presencia de la tensión de suministro de la instalación.
⚪
B)
Medida de aislamiento de la tensión de suministro de la instalación.
⚪
C)
Medida de aislamiento con relación a tierra.
⚪
D)
B y C
PREGUNTA 3 de 20
Que es un chispómetro:
⚪
A)
Es un aparato para la medida de resistencia de aislamiento.
⚪
B)
Es un aparato para la medida de la resistencia de tierra.
⚪
C)
Es un aparato que mide la intensidad de chispas.
⚪
D)
Es un aparato para la medida de la rigidez dieléctrica.
PREGUNTA 4 de 20
Cuál es el inconveniente de utilizar aire comprimido para la eliminación de contaminación superficial en los devanados de una máquina:
⚪
A)
En ocasiones se quita la suciedad de un sitio para que quede depositada en otro
⚪
B)
Es método costoso y además muy ruidoso.
⚪
C)
Requiere una cierta pericia por parte del operario.
⚪
D)
No se puede realizar con la máquina en marcha.
PREGUNTA 5 de 20
Qué técnica de mantenimiento es posible utilizar para diagnosticar un desequilibrado de rotor en una máquina eléctrica rotativa:
⚪
A)
Endoscopia
⚪
B)
Partículas magnéticas
⚪
C)
Análisis de vibraciones
⚪
D)
Inspección por ultrasonido
PREGUNTA 6 de 20
Con qué parámetro deben corregirse las medidas de resistencia de aislamiento realizado con el megómetro
⚪
A)
Con la tensión eléctrica aplicada
⚪
B)
Con el tiempo
⚪
C)
Con la ultima lectura de resistencia
⚪
D)
Con la temperatura
PREGUNTA 7 de 20
Por qué se deben mantener apretadas las conexiones eléctricas en instalaciones
⚪
A)
Las averías causadas por fallos de conexión eléctrica pueden requerir mucho tiempo para solucionarlas
⚪
B)
Una conexión floja puede ocasionar el deterioro del contacto por la formación de oxido
⚪
C)
Las conexiones pueden desapretarse debido a cambios de temperatura y a vibraciones
⚪
D)
Todas son correctas
PREGUNTA 8 de 20
Por qué parámetro está limitado la clase de aislamiento normalizado
⚪
A)
Por la temperatura
⚪
B)
Por la tensión nominal
⚪
C)
Por la humedad
⚪
D)
Apartado A y C.
PREGUNTA 9 de 20
Para comprobar el estado y desgaste de los cojinetes de una máquina rotativa la técnica a utilizar consiste en
⚪
A)
Realizar análisis de vibraciones
⚪
B)
Medir el entrehierro en diferentes zonas de la periferia del estator
⚪
C)
Comprobar el movimiento vertical del extremo libre del eje
⚪
D)
Todas las anteriores
PREGUNTA 10 de 20
Cómo se denomina el tipo de seccionador A.T. que puede cortar y reponer corrientes nominales, cortar pequeñas sobrecargas, pero no eliminar cortocircuitos
⚪
A)
Seccionador con enclavamiento
⚪
B)
Seccionador en carga
⚪
C)
Ruptofusible
⚪
D)
Seccionador de puesta a tierra
PREGUNTA 11 de 20
Cómo se denomina la clase de servicio normalizado en el que una máquina eléctrica trabaja a carga constante de modo que alcanza la temperatura de régimen permanente
⚪
A)
Servicio continuo
⚪
B)
Servicio temporal
⚪
C)
Servicio intermitente
⚪
D)
Servicio ininterrumpido
PREGUNTA 12 de 20
La medida de aislamientos de equipos se realiza con:
⚪
A)
Tester
⚪
B)
Óhmetro
⚪
C)
Megóhmetro o megger
⚪
D)
Cualquiera de los tres
PREGUNTA 13 de 20
Los aparatos de medidas de baja tensión trabajan con una tensión máxima de
⚪
A)
250 V
⚪
B)
500 V
⚪
C)
1000 V
⚪
D)
750 V
PREGUNTA 14 de 20
¿En qué consiste la lubricación hidrodinámica de película fina?
⚪
A)
La película lubricante dispone de aditivo para operar bajo régimen de altas cargas.
⚪
B)
La película lubricante es de suficiente espesor para separar por completo las dos superficies, existiendo fricción fluida.
⚪
C)
La película lubricante dispone de aditivo para operar de forma intermitente.
⚪
D)
La película lubricante es de suficiente espesor para separar por completo las dos superficies, no existiendo fricción fluida
PREGUNTA 15 de 20
El transductor más adecuado para tomar datos de vibración a alta frecuencia (>1000Hz) en instrumentos de medida de vibración es
⚪
A)
Transductor de aceleración (piezoeléctrico
⚪
B)
Transductor de velocidad (tipo sísmico
⚪
C)
Transductor de desplazamiento (corriente de fugas
⚪
D)
Transductor extensométrico (tipo galga
PREGUNTA 16 de 20
¿Cómo se denomina la ¿fluctuación? en la alimentación eléctrica que provoca parpadeo en los sistemas de iluminación?
⚪
A)
Distorsión armónica
⚪
B)
Flicker
⚪
C)
Hueco
⚪
D)
sobretensión
PREGUNTA 17 de 20
Es posible hacer la medida de rigidez dieléctrica sobre un material aislante sólido?
⚪
A)
No, debido al problema de seguridad que se plantea
⚪
B)
Sí, pero el ensayo es destructivo dejando el material en estado irreversible
⚪
C)
Sí, pero sólo en el caso de que el aislante sea dieléctrico
⚪
D)
Depende del tipo de material a ensayar
PREGUNTA 18 de 20
La técnica predictiva especialmente indicada para realizar control de calidad en uniones soldadas es:
⚪
A)
Partículas magnéticas
⚪
B)
Líquidos penetrantes
⚪
C)
Inspección radiográfica
⚪
D)
Ultrasonidos
PREGUNTA 19 de 20
Para estudiar mediante análisis de vibraciones el desequilibrio dinámico del rotor de una máquina rotativa es posible conectar el acelerómetro
⚪
A)
En dirección axial
⚪
B)
En dirección radial
⚪
C)
Indistintamente en dirección axial o radial
⚪
D)
Sin coincidir con la dirección axial o radial
PREGUNTA 20 de 20
Para realizar análisis cuantitativo de temperatura sobre un material determinado, mediante un equipo de termografia infrarroja, el parámetro más importante a configurar es:
⚪
A)
La absortividad
⚪
B)
La reflectividad
⚪
C)
La emisividad
⚪
D)
La distancia al objeto de media
Este test aún no tiene comentarios 🤔