PREGUNTA 1 de 20
Las aleaciones de aluminio para chapas de construcción naval (serie 5000) están compuestas principalmente por aluminio y magnesio.
⚪
A)
y se incluyen dentro de las no tratables térmicamente.
⚪
B)
y son endurecibles por precipitación.
⚪
C)
y están endurecidas por temple y revenido.
⚪
D)
La afirmación es falsa porque el aluminio no tiene aplicaciones estructuras en construcción naval.
PREGUNTA 2 de 20
Se dice que una aleación es tratable térmicamente
⚪
A)
cuando pueden eliminarse las tensiones residuales mediante el tratamiento térmico de recocido.
⚪
B)
cuando no se puede endurecer por acritud.
⚪
C)
cuando es posible endurecerla por formación de martensita o por precipitación.
⚪
D)
si sólo es hechurable a una temperatura superior a la de recristalización.
PREGUNTA 3 de 20
Ausrevenido
⚪
A)
es el tratamiento térmico de revenido para transformar la bainita en perlita.
⚪
B)
es un tratamiento isotérmico para obtener bainita.
⚪
C)
consiste en el revenido de la Austenita para obtener austenita revenida
⚪
D)
es un tratamiento térmico para transformar la austenita en martensita revenida.
PREGUNTA 4 de 20
Las aleaciones ligeras
⚪
A)
destacan por su facilidad y rapidez de procesado.
⚪
B)
incluyen a las aleaciones de Al, de Cu y de Mg.
⚪
C)
son las que tienen como metal base Al, Ti o Mg.
⚪
D)
son aleaciones férreas que destacan por su baja densidad
PREGUNTA 5 de 20
Los aceros microaleados
⚪
A)
se incluyen dentro de los de alto carbono
⚪
B)
deben su mayor resistencia a su alta aleación
⚪
C)
son más blandos y dúciles que sus equivalentes al carbono ordinario
⚪
D)
están endurecidos por un grano ultrafino de ferrita y precipitados de carburos de aleantes
PREGUNTA 6 de 20
¿Cuál es aproximadamente el contenido mínimo de Cromo que debe tener un acero para que sea inoxidable (en ausencia de otros elementos de aleación)?
⚪
A)
5% de Cr
⚪
B)
25% de Cr
⚪
C)
11% de Cr
⚪
D)
1% de Cr
PREGUNTA 7 de 20
Los materiales compuestos de matriz polimérica reforzada con fibras a) Los materiales compuestos de matriz polimérica reforzada con fibras
⚪
A)
destacan por sus elevadas resistencia y rigidez específicas.
⚪
B)
sólo pueden fabricarse con fibras continuas alineadas.
⚪
C)
son muy importantes en la industria aeronáutica pero no tienen aplicación en la construcción naval.
⚪
D)
presentan una resistencia que disminuye conforme aumenta la fracción en volumen de fibra.
PREGUNTA 8 de 20
Los materiales compuestos de matriz metálica reforzados con partículas:
⚪
A)
experimentan siempre el mismo mecanismo de reforzamiento.
⚪
B)
deben su reforzamiento a una transferencia de parte del esfuerzo aplicado a las partículas por parte de la matriz
⚪
C)
las partículas no refuerzan, su cometido es puramente estético.
⚪
D)
experimentan mecanismos de reforzamiento dependientes del tamaño de las partículas
PREGUNTA 9 de 20
En un material reforzado con fibras alineadas, cuando se aplica una tensión paralela a las fibras, ¿Cuál es la eficiencia del reforzamiento sobre la matriz?
⚪
A)
0
⚪
B)
1
⚪
C)
1/2
⚪
D)
1/5
PREGUNTA 10 de 20
En la microestructura resultante del enfriamiento lento de un acero hipereutectoide hasta temperatura ambiente desde la condición austenítica
⚪
A)
la fase proeutectoide es la cementita más la austenita.
⚪
B)
la fase primaria es la ferrita.
⚪
C)
no siempre existe perlita.
⚪
D)
Ninguna de las afirmaciones anteriores es cierta.
PREGUNTA 11 de 20
La velocidad de difusión (difusividad) atómica en sólidos es mayor
⚪
A)
al aumentar el gradiente de concentración.
⚪
B)
al disminuir la temperatura
⚪
C)
en el mecanismo intersticial
⚪
D)
Ninguna de las afirmaciones anteriores es cierta.
PREGUNTA 12 de 20
En la difusión atómica en estado estacionario el flujo neto de átomos es proporcional a
⚪
A)
al gradiente de concentración
⚪
B)
la temperatura
⚪
C)
la difusividad o coeficiente de difusión
⚪
D)
al número de átomos por unidad de volumen
PREGUNTA 13 de 20
En los diagramas de fases de sistemas isomórficos binarios
⚪
A)
la solubilidad es total en solido y parcial en liquido
⚪
B)
la solubilidad es total en liquido y parcial en solico
⚪
C)
la solubilidad es total tanto en estado líquido como sólido
⚪
D)
existen dos fases solidas
PREGUNTA 14 de 20
En los cuproníqueles (aleaciones Cu-Ni) utilizados para tuberías
⚪
A)
se consigue un elevado endurecimiento debido a la formación de precipitados.
⚪
B)
el aumento de la resistencia se debe a la solución sólida del Ni en Cu.
⚪
C)
se forma una segunda fase cuando la concentración de Ni es mayor del 30%
⚪
D)
la microestructura puede variar mucho en función de la composición de la aleación (%Ni)
PREGUNTA 15 de 20
Las aleaciones de composición eutéctica se emplean habitualmente para
⚪
A)
obtener piezas por colada (de fundición).
⚪
B)
obtener piezas de altas características mecánicas.
⚪
C)
obtener piezas por forja (conformación plástica).
⚪
D)
obtener piezas por deformación en frío.
PREGUNTA 16 de 20
El endurecimiento por dispersión eficaz
⚪
A)
disminuye cuando las partículas de la segunda fase son duras y frágiles
⚪
B)
aumenta cuando disminuye el tamaño de las partículas
⚪
C)
disminuye cuando aumenta la cantidad de segunda fase
⚪
D)
Ninguna de las afirmaciones anteriores es cierta.
PREGUNTA 17 de 20
Una de las diferencias entre los diagramas TTT de aceros y el diagrama de fases Fe-C es
⚪
A)
que los diagramas TTT únicamente son válidos para aceros al carbono ordinario eutectoides (0.77%C)
⚪
B)
que en los diagramas TTT nunca aparecen fases proeutectoides
⚪
C)
que en los diagramas de fase no aparece el microconstituyente eutectoide denominado perlita.
⚪
D)
que en los diagramas de fase se contemplan todas las aleaciones posibles dentro del sistema Fe-C.
PREGUNTA 18 de 20
La fase martensita tiene una elevada fragilidad
⚪
A)
debido a la baia solubilidad del carbono en su estructura.
⚪
B)
debido a su estructura cristalina BCT.
⚪
C)
porque a temperatura ambiente la difusión atómica es muy lenta.
⚪
D)
en función del elevado número de sistemas de deslizamiento de dislocaciones en la estructura BCT.
PREGUNTA 19 de 20
La perlita
⚪
A)
es más resistente que la bainita para una misma composición del acero.
⚪
B)
es una fase compuesta por agujas de cementita en una matriz ferrítica.
⚪
C)
está constituida por láminas alternas de cementita y ferrita.
⚪
D)
es consecuencia de la descomposición eutectoide de la austenita a temperaturas inferiores a 550°C.
PREGUNTA 20 de 20
La esferoidita
⚪
A)
es la fase más estable posible en un acero eutectoide.
⚪
B)
es algo más dura que la martensita, pero mucho más dúctil y tenaz.
⚪
C)
se obtiene calentando la perlita a 700°C durante 24 horas.
⚪
D)
es un microconstituyente de los aceros que consiste en agujas de Fe;C en una matriz ferrítica.
Este test aún no tiene comentarios 🤔